[. . . ] Product figure VL-MWD501EX VL-WD613EX VL-V554EX (surface mount)/ VL-V554UEX (flush mount) R The illustrations in the supplied manual(s) may vary slightly from the actual product. Caution: R Before attempting to connect or operate this product, please read the label on the rear of the main monitor. 1 Supplied accessories For the sub monitor Accessory item AC adaptor/ PNLV226CE*1 Quantity 1 AC adaptor/ PNLV226E*1 1 Rechargeable batteries 2 Charger 1 *1 Appropriately dispose of the AC adaptor that will not be used. Note: R Accessories for installing the main monitor and the doorphone are described in the supplied Installation Guide. [. . . ] : ® : Select the camera you want to ( ) – The monitoring time is about 3 minutes. R Making a warning sound come out of the camera: : Touch [Play sound]. : ( – – – ) ( )® : "Warning" ® ® [Warning sound] ® monitor with. 3 To end the operation, press Features available while monitoring – – – – Features available when a sensor is triggered Adjust wide/zoom and pan/tilt settings (® page 33) Adjust brightness settings (® page 34) Record monitored images (® page 20) Adjust wide/zoom and pan/tilt settings (® page 33) Adjust sound and display settings (® page 33) Make a warning sound come out of the camera (® page 24) Record monitored images (® page 20) Note: R Monitoring time: – : About 90 seconds (can be extended up to 3 minutes by performing operations during monitoring) – : About 3 minutes R In situations where it is difficult to see images, such as when it is dark or when there is backlight, change the camera’s [Brightness] setting and activate the [Backlight compensation] setting as required. (® page 27) Note: R Images from when camera sensors are triggered are automatically recorded to the SD card. (® page 25) R Once a sensor is triggered, the next sensor detection cannot be made until about 10 seconds after the first triggered images have finished being displayed. ® page 26) R In situations where it is difficult to see images, such as when it is dark or when there is backlight, change the camera’s [Brightness] setting and activate the [Backlight compensation] setting as required. (® page 27) R The volume and the types of sounds used by the [Warning sound] setting can be changed. 3 When camera sensors are triggered When a camera sensor is triggered, the main monitor and sub monitor are notified in the follow manner. 4 Turning off camera sensor detections for specified periods of time (main monitor only) Camera sensor detections can be turned off for specified periods of times as required. € When camera sensor detections are turned off, notifications are not sent to the main monitor and sub monitor and images are not automatically recorded. Note: R The setting function screen automatically quits if an incoming call is received or if no operations are performed for about 90 seconds. Item name: Sensor settings Function name Sensor selection Heat sensor detection*1 Setting contents and other information Heat sensor only, <Heat sensor + motion detection>, External sensor only, All sensors, Off (disables all sensors) <Night only>, Always R Select the time period for heat sensor detection. € When [Night only] is selected, the heat sensor operates according to the settings of [Day and night switch] (® page 26). Day only, <Always> R Select the time period for motion detection. € When [Day only] is selected, motion detection operates according to the settings of [Day and night switch] (® page 26). <Auto>, Timer R Select whether to automatically set the day and night switch settings or set them manually to a preferred time. € This setting is active when the [Heat sensor detection] or [Motion detection] settings are set to [Night only] or [Day only]. Auto: the camera automatically switches between night and day modes depending on the brightness of the surrounding area. (After selecting [Timer], set the time with [+] and [–], and then touch [OK]. ) Time with no detection <10 seconds>, 30 seconds, 60 seconds R Select the time after an image is detected by a sensor or a monitored image is displayed until the sensor can make detections again. € Select a long time period if you do not want the sensor to make frequent detections. [. . . ] R Because of the characteristics of the sensors, the camera may not be able to detect people moving towards the front of the camera. € Change the camera location so that objects pass the camera from the sides. (It is easier to detect objects moving sideways in front of the camera. ) – If you want to detect objects moving towards the front of the camera, use a commercially available external sensor. [. . . ]